LaserCSC¶

class lsst.ts.tunablelaser.LaserCSC(initial_state=State.STANDBY, config_dir=None, simulation_mode=0, override='')¶

Bases: ConfigurableCsc

This is the class that implements the TunableLaser CSC.

Parameters:

initial_statelsst.ts.salobj.State, optional: The initial state that a CSC will start up in. Only useful for unit tests as most CSCs will start in salobj.State.STANDBY
config_dirpathlib.Path, optional: Path where the configuration files are located; typically used for unit tests.
simulation_modebool, optional: Is the laser being simulated?
overridestr, optional: The name of the override config file to use, if any.

Attributes:

modelLaser: The model of the laser component which handles the actual hardware.
telemetry_ratefloat: The amount of time to wait for telemetry to publish.
telemetry_taskasyncio.Future: The task that tracks the state of the telemetry loop.
simulatorMainLaserServer or StubbsLaserServer: The mock simulator if in simulation mode.

Attributes Summary

`config_dir`	Get or set the configuration directory.
`connected`
`default_initial_state`
`disabled_or_enabled`	Return True if the summary state is `State.DISABLED` or `State.ENABLED`.
`domain`
`enable_cmdline_state`
`simulation_help`
`simulation_mode`	Get the current simulation mode.
`simulator_fails_to_start`
`summary_state`	Get the summary state as a `State` enum.
`valid_simulation_modes`
`version`

Methods Summary

`add_arguments`(parser)	Add arguments to the parser created by `make_from_cmd_line`.
`add_kwargs_from_args`(args, kwargs)	Add constructor keyword arguments based on parsed arguments.
`amain`(index, **kwargs)	Make a CSC from command-line arguments and run it.
`assert_enabled`([action])	Assert that an action that requires ENABLED state can be run.
`assert_substate`(substates, action)	Assert that the action is happening while in the PropagatingState.
`begin_disable`(data)	Begin do_disable; called before state changes.
`begin_enable`(data)	Begin do_enable; called before state changes.
`begin_exitControl`(data)	Begin do_exitControl; called before state changes.
`begin_standby`(data)	Begin do_standby; called before the state changes.
`begin_start`(data)	Begin do_start; configure the CSC before changing state.
`check_for_duplicate_heartbeat`([num_messages])	Monitor heartbeat events and return True if any have a different private_origin.
`close`([exception, cancel_start])	Shut down, clean up resources and set done_task done.
`close_tasks`()	Tasks to perform before closing the CSC.
`configure`(config)	Configure the CSC.
`do_changeTempCtrlSetpoint`(data)	Change the set point of the laser thermal reader.
`do_changeWavelength`(data)	Change the wavelength of the laser.
`do_clearLaserFault`(data)	Clear the hardware fault state of the laser by turning the power register off.
`do_disable`(data)	Transition from `State.ENABLED` to `State.DISABLED`.
`do_enable`(data)	Transition from `State.DISABLED` to `State.ENABLED`.
`do_exitControl`(data)	Transition from `State.STANDBY` to `State.OFFLINE` and quit.
`do_setBurstMode`(data)	Set burst mode for the laser.
`do_setContinuousMode`(data)	Set continuous mode for the laser.
`do_setLogLevel`(data)	Set logging level.
`do_setOpticalConfiguration`(data)	Change Optical Alignment of the laser. Parameters ---------- data - with property 'configuration' setting optical alignment of the laser.
`do_standby`(data)	Transition from `State.DISABLED` or `State.FAULT` to `State.STANDBY`.
`do_start`(data)	Transition from `State.STANDBY` to `State.DISABLED`.
`do_startPropagateLaser`(data)	Change the state to the Propagating State of the laser.
`do_stopPropagateLaser`(data)	Stop the Propagating State of the laser.
`do_triggerBurst`(data)	Trigger a burst.
`do_turnOffTempCtrl`(data)	Turn off the run mode of the laser thermal reader.
`do_turnOnTempCtrl`(data)	Turn on the run mode of the laser thermal reader.
`end_disable`(data)	End do_disable; called after state changes but before command acknowledged.
`end_enable`(data)	End do_enable; called after state changes but before command acknowledged.
`end_exitControl`(data)	End do_exitControl; called after state changes but before command acknowledged.
`end_standby`(data)	End do_standby; called after state changes but before command acknowledged.
`end_start`(data)	End do_start; called after state changes but before command acknowledged.
`fault`(code, report[, traceback])	Enter the fault state and output the `errorCode` event.
`get_config_pkg`()	Return the configuration package name.
`handle_summary_state`()	Handle the summary state transitons.
`implement_simulation_mode`(simulation_mode)	Implement going into or out of simulation mode.
`make_from_cmd_line`(index[, check_if_duplicate])	Construct a CSC from command line arguments.
`publish_new_detailed_state`(new_sub_state)	Publish the updated detailed state.
`put_log_level`()	Output the logLevel event.
`read_config_dir`()	Read the config dir and put configurationsAvailable if changed.
`read_config_dir_loop`()
`read_config_files`(config_validator, ...[, ...])	Read a set of configuration files and return the validated config.
`set_simulation_mode`(simulation_mode)	Set the simulation mode.
`signal_handler`()	Handle termination signals.
`start`()	Finish constructing the CSC.
`start_phase2`()	Handle the initial state.
`telemetry`()	Send out the TunableLaser's telemetry.

Attributes Documentation

config_dir¶

Get or set the configuration directory.

Parameters:

config_dirstr, pathlib.Path: New configuration directory.

Returns:

config_dirpathlib.Path: Absolute path to the configuration directory.

Raises:

ValueError: If the new configuration dir is not a directory.

connected¶

default_initial_state: State = 5¶

disabled_or_enabled¶

Return True if the summary state is State.DISABLED or State.ENABLED.

This is useful in handle_summary_state to determine if you should start or stop a telemetry loop, and connect to or disconnect from an external controller

domain¶

enable_cmdline_state = False¶

simulation_help: str | None = None¶

simulation_mode¶

Get the current simulation mode.

0 means normal operation (no simulation).

Raises:

ExpectedError: If the new simulation mode is not a supported value.

simulator_fails_to_start = False¶

summary_state¶: Get the summary state as a State enum.

valid_simulation_modes: Sequence[int] = (<SimulationMode.OFF: 0>, <SimulationMode.ON: 1>, <SimulationMode.MOCK_INSTABILITY: 2>)¶

version = '?'¶

Methods Documentation

classmethod add_arguments(parser: ArgumentParser) → None¶

Add arguments to the parser created by make_from_cmd_line.

Parameters:

parserargparse.ArgumentParser: The argument parser.

Notes

If you override this method then you should almost certainly override add_kwargs_from_args as well.

classmethod add_kwargs_from_args(args: Namespace, kwargs: dict[str, Any]) → None¶

Add constructor keyword arguments based on parsed arguments.

Parameters:

argsargparse.Namespace: Parsed command.
kwargsdict: Keyword argument dict for the constructor. Update this based on args. The index argument will already be present if relevant.

Notes

If you override this method then you should almost certainly override add_arguments as well.

async classmethod amain(index: int | IntEnum | bool | None, **kwargs: Any) → None¶

Make a CSC from command-line arguments and run it.

Parameters:

indexint, enum.IntEnum, True, or None

If the CSC is indexed, do one of the following:

Specify True to make index a required command-line argument that accepts any nonzero index.
Specify an enum.IntEnum class to make index a required command-line argument that only accepts the enum values.
Specify a non-zero integer to use that index. This is rare; if the CSC is indexed then the user should usually be allowed to specify the index.

If the CSC is not indexed, specify None or 0.

**kwargsdict, optional

Additional keyword arguments for your CSC’s constructor.

assert_enabled(action: str = '') → None¶

Assert that an action that requires ENABLED state can be run.

Parameters:

actionstr, optional: Action attempted. Not needed if this is called at the beginning of a do_... method, since the user will know what command was called.

assert_substate(substates, action)¶

Assert that the action is happening while in the PropagatingState.

Parameters:

substateslist: A list of allowed states
actionstr: The name of the command being sent.

Raises:

salobj.ExpectedError: Raised when an action is not allowed in a substate.

async begin_disable(data: BaseMsgType) → None¶

Begin do_disable; called before state changes.

Parameters:

dataDataType: Command data

async begin_enable(data: BaseMsgType) → None¶

Begin do_enable; called before state changes.

Parameters:

dataDataType: Command data

async begin_exitControl(data: BaseMsgType) → None¶

Begin do_exitControl; called before state changes.

Parameters:

dataDataType: Command data

async begin_standby(data: BaseMsgType) → None¶

Begin do_standby; called before the state changes.

Parameters:

dataDataType: Command data

async begin_start(data: BaseMsgType) → None¶

Begin do_start; configure the CSC before changing state.

Parameters:

datacmd_start.DataType: Command data

Notes

The override field must be one of:

The name of a config label or config file
The name and version of a config file, formatted as <file_name>:<version>, where the version is a git reference, such as a git tag or commit hash. This form does not support labels.

async check_for_duplicate_heartbeat(num_messages: int = 5) → int¶

Monitor heartbeat events and return True if any have a different private_origin.

Intended for use by check_if_duplicate.

The heartbeat loop should be running before this is called. This avoids the issue that if 2 CSCs are started at the same time then neither will see the other one’s heartbeat. This code also assumes that will be true; it will likely raise asyncio.TimeoutError if not.

Parameters:

num_messagesfloat: The number of heartbeat messages to read.

Returns:

originint: private_origin field of duplicate heartbeat, or 0 if none detected.

Raises:

asyncio.TimeoutError: If no heartbeat seen within the specified time.

async close(exception: Exception | None = None, cancel_start: bool = True) → None¶

Shut down, clean up resources and set done_task done.

May be called multiple times. The first call closes the Controller; subsequent calls wait until the Controller is closed.

Subclasses should override close_tasks instead of close, unless you have a good reason to do otherwise.

Parameters:

exceptionException, optional: The exception that caused stopping, if any, in which case the self.done_task exception is set to this value. Specify None for a normal exit, in which case the self.done_task result is set to None.
cancel_startbool, optional: Cancel the start task? Leave this true unless calling this from the start task.

Notes

Removes the SAL log handler, calls close_tasks to stop all background tasks, pauses briefly to allow final SAL messages to be sent, then closes the domain.

async close_tasks()¶

Tasks to perform before closing the CSC.

Cancel telemetry
If laser is propagating, stop it.
Disconnect from the laser
If simulator is running, shut it off

async configure(config)¶: Configure the CSC.

async do_changeTempCtrlSetpoint(data)¶: Change the set point of the laser thermal reader.

async do_changeWavelength(data)¶

Change the wavelength of the laser.

Parameters:

data

async do_clearLaserFault(data)¶

Clear the hardware fault state of the laser by turning the power register off.

Parameters:

data

async do_disable(data: BaseMsgType) → None¶

Transition from State.ENABLED to State.DISABLED.

Parameters:

datacmd_disable.DataType: Command data

async do_enable(data: BaseMsgType) → None¶

Transition from State.DISABLED to State.ENABLED.

Parameters:

datacmd_enable.DataType: Command data

async do_exitControl(data: BaseMsgType) → None¶

Transition from State.STANDBY to State.OFFLINE and quit.

Parameters:

datacmd_exitControl.DataType: Command data

async do_setBurstMode(data)¶

Set burst mode for the laser.

Burst mode changes the propagation to pulse the laser with increased power at a regular interval.

Parameters:

dataDataType: The command data.

async do_setContinuousMode(data)¶

Set continuous mode for the laser.

Continuous mode changes the propagation to pulse continuously at a regular power level.

Parameters:

dataDataType: The command data.

async do_setLogLevel(data: BaseMsgType) → None¶

Set logging level.

Parameters:

datacmd_setLogLevel.DataType: Logging level.

async do_setOpticalConfiguration(data)¶: Change Optical Alignment of the laser. Parameters ———- data - with property ‘configuration’ setting optical

alignment of the laser.

async do_standby(data: BaseMsgType) → None¶

Transition from State.DISABLED or State.FAULT to State.STANDBY.

Parameters:

datacmd_standby.DataType: Command data

async do_start(data: BaseMsgType) → None¶

Transition from State.STANDBY to State.DISABLED.

Parameters:

datacmd_start.DataType: Command data

async do_startPropagateLaser(data)¶

Change the state to the Propagating State of the laser.

Parameters:

data

async do_stopPropagateLaser(data)¶

Stop the Propagating State of the laser.

Parameters:

data

async do_triggerBurst(data)¶: Trigger a burst.

async do_turnOffTempCtrl(data)¶: Turn off the run mode of the laser thermal reader.

async do_turnOnTempCtrl(data)¶: Turn on the run mode of the laser thermal reader.

async end_disable(data: BaseMsgType) → None¶

End do_disable; called after state changes but before command acknowledged.

Parameters:

dataDataType: Command data

async end_enable(data: BaseMsgType) → None¶

End do_enable; called after state changes but before command acknowledged.

Parameters:

dataDataType: Command data

async end_exitControl(data: BaseMsgType) → None¶

End do_exitControl; called after state changes but before command acknowledged.

Parameters:

dataDataType: Command data

async end_standby(data: BaseMsgType) → None¶

End do_standby; called after state changes but before command acknowledged.

Parameters:

dataDataType: Command data

async end_start(data: BaseMsgType) → None¶

End do_start; called after state changes but before command acknowledged.

Parameters:

dataDataType: Command data

async fault(code: int | None, report: str, traceback: str = '') → None¶

Enter the fault state and output the errorCode event.

Parameters:

codeint: Error code for the errorCode event. If None then errorCode is not output and you should output it yourself. Specifying None is deprecated; please always specify an integer error code.
reportstr: Description of the error.
tracebackstr, optional: Description of the traceback, if any.

static get_config_pkg()¶: Return the configuration package name.

async handle_summary_state()¶: Handle the summary state transitons.

async implement_simulation_mode(simulation_mode: int) → None¶

Implement going into or out of simulation mode.

Deprecated. See simulation mode for details.

Parameters:

simulation_modeint: Requested simulation mode; 0 for normal operation.

Raises:

ExpectedError: If simulation_mode is not a supported value.

classmethod make_from_cmd_line(index: int | IntEnum | bool | None, check_if_duplicate: bool = False, **kwargs: Any) → BaseCsc¶

Construct a CSC from command line arguments.

Parameters:

indexint, enum.IntEnum, True, or None

If the CSC is indexed, do one of the following:

Specify True to make index a required command-line argument that accepts any nonzero index.
Specify an enum.IntEnum class to make index a required command-line argument that only accepts the enum values.
Specify a non-zero integer to use that index. This is rare; if the CSC is indexed then the user should usually be allowed to specify the index.

If the CSC is not indexed, specify None or 0.

check_if_duplicatebool, optional

Check for heartbeat events from the same SAL name and index at startup (before starting the heartbeat loop)? The default is False, to match the BaseCsc default. Note: handled by setting the attribute directly instead of as a constructor argument, because CSCs may not all support the constructor argument.

**kwargsdict, optional

Additional keyword arguments for your CSC’s constructor.

Returns:

csccls: The CSC.

Notes

To add additional command-line arguments, override add_arguments and add_kwargs_from_args.

async publish_new_detailed_state(new_sub_state)¶

Publish the updated detailed state.

Parameters:

new_sub_stateLaserDetailedState: The new sub state to publish.

async put_log_level() → None¶: Output the logLevel event.

async read_config_dir() → None¶

Read the config dir and put configurationsAvailable if changed.

Output the configurationsAvailable event (if changed), after updating the overrides and version fields. Also update the version field of evt_configurationApplied, in preparation for the next time the event is output.

async read_config_dir_loop() → None¶

classmethod read_config_files(config_validator: Draft7Validator, config_dir: Path, files_to_read: list[str], git_hash: str = '') → SimpleNamespace¶

Read a set of configuration files and return the validated config.

Parameters:

config_validatorjsonschema validator: Schema validator for configuration.
config_dirpathlib.Path: Path to config files.
files_to_readList [str]: Names of files to read, with .yaml suffix. Empty names are ignored (a useful feature for BaseConfigTestCase). The files are read in order, with each later file overriding values that have been accumulated so far.
git_hashstr, optional: Git hash to use for the files. “” if current.

Returns:

types.SimpleNamespace: The validated config as a simple namespace.

Raises:

ExpectedError: If the specified configuration files cannot be found, cannot be parsed as yaml dicts, or produce an invalid configuration (one that does not match the schema).

async set_simulation_mode(simulation_mode: int) → None¶

Set the simulation mode.

Await implement_simulation_mode, update the simulation mode property and report the new value.

Parameters:

simulation_modeint: Requested simulation mode; 0 for normal operation.

signal_handler() → None¶: Handle termination signals.

async start() → None¶

Finish constructing the CSC.

Call set_simulation_mode. If this fails, set self.start_task to the exception, call stop, making the CSC unusable, and return.
Call handle_summary_state
Set self.start_task done.

async start_phase2() → None¶

Handle the initial state.

Called after start.

async telemetry()¶: Send out the TunableLaser’s telemetry.

Navigation

LaserCSC¶